by Rima Chatterjee
A flashing reset button on a gas boiler is a common issue that often indicates a problem within the boiler system. This comprehensive guide will provide you with a detailed understanding of the common reasons for a flashing reset button, the steps to reset the boiler, and the technical specifications you need to know to effectively troubleshoot and address the issue.
Common Reasons for a Flashing Reset Button
- Fault or Error: The flashing reset button is a clear indication of a fault or error within the boiler system. This could be related to various components, such as:
- Fan Unit: A malfunctioning fan unit can cause the reset button to flash, as the boiler’s safety controls may detect an issue with the air pressure or airflow.
- Air Pressure Switch: Issues with the air pressure switch, which monitors the air pressure within the boiler, can also trigger the reset button to flash.
Ignition System: Problems with the ignition system, such as a faulty spark generator or flame sensor, can lead to a flashing reset button.
Low Pressure: Low boiler pressure can cause the reset button to flash. This may be due to:
- Water Leaks: Leaks in the boiler system or the associated pipework can result in a gradual loss of water pressure, leading to the reset button flashing.
- Malfunctioning Pressure Relief Valve: A faulty pressure relief valve that is not functioning correctly can cause the boiler pressure to drop, triggering the reset button.
Issues with the Filling Loop: Problems with the boiler’s filling loop, which is used to top up the water level, can also contribute to low pressure and a flashing reset button.
Overheating: Overheating within the boiler system can cause the reset button to flash. This can be due to:
- Faulty Thermostat: A malfunctioning thermostat that is not accurately controlling the boiler’s temperature can lead to overheating and a flashing reset button.
- Blocked Heat Exchanger: A blocked or partially blocked heat exchanger can prevent the efficient transfer of heat, leading to overheating and the reset button flashing.
Circulation Pump Issues: Problems with the boiler’s circulation pump, such as a failure or blockage, can result in poor water circulation and overheating, triggering the reset button.
Gas Supply Issues: Problems with the gas supply to the boiler can also cause the reset button to flash. This may include:
- Gas Valve Malfunction: A faulty gas valve that is not opening or closing properly can disrupt the gas supply and lead to a flashing reset button.
- Gas Pressure Irregularities: Fluctuations or irregularities in the gas pressure can trigger the reset button to flash as the boiler’s safety controls detect an issue.
Gas Supply Interruptions: Temporary interruptions in the gas supply, such as a problem with the gas mains, can also cause the reset button to flash.
Other Faults: The flashing reset button may also indicate other malfunctions within the boiler system, including:
- Ignition Issues: Problems with the boiler’s ignition system, such as a faulty spark generator or flame sensor, can lead to a flashing reset button.
- Pump Faults: Issues with the boiler’s circulation pump, such as a failure or blockage, can contribute to the reset button flashing.
- Fan Malfunctions: Problems with the boiler’s fan unit, such as a failure or blockage, can also trigger the reset button to flash.
- Sensor Faults: Malfunctioning sensors, such as those monitoring water temperature or pressure, can cause the reset button to flash.
Steps to Reset the Boiler
Consult the Boiler Manual: Before attempting to reset the boiler, it is crucial to refer to the manufacturer’s instructions in the boiler manual. This will provide you with the specific reset procedure for your boiler model, including the location of the reset button and the recommended duration for holding it down.
Push the Reset Button: Locate the reset button, which is typically situated on the front of the boiler and may be labelled with a flame or a cross symbol. Hold the button down for the recommended time, usually between 3 to 10 seconds, and wait for the boiler to start up. If the reset is successful, the flashing light should become steady, and the error code on the display may disappear.
Repeat if Necessary: If the boiler doesn’t restart after the initial reset attempt, you can repeat the process up to two more times. However, it is important to avoid repeatedly pressing the reset button, as this can potentially damage the control panel.
Call a Professional: If the boiler still doesn’t restart after three reset attempts, it is likely that there is a more serious fault that requires the assistance of a Gas Safe registered engineer. Attempting to diagnose and repair the issue without the proper expertise can be dangerous and may lead to further damage to the boiler.
Technical Specifications
- Reset Button Location: The reset button is usually located on the front of the boiler and may be labelled with a flame or a cross symbol.
- Reset Procedure: The reset procedure typically involves holding the button down for a specified time, usually between 3 to 10 seconds, and waiting for the boiler to start up.
- Error Codes: Modern boilers often display error codes when they go into lockout. These codes can be used by a qualified engineer to diagnose the specific problem with the boiler and determine the appropriate course of action.
DIY Considerations
While some initial troubleshooting steps can be taken, it is generally recommended to seek the assistance of a qualified heating engineer to ensure the safe and efficient operation of the boiler. Attempting DIY repairs can lead to further damage or safety risks, as gas boilers are complex systems that require specialized knowledge and tools to maintain and repair.
References
- PHS Engineers Ltd. (n.d.). Red Light Flashing on Boiler? Common Reasons & How to Fix It. Retrieved from https://phsengineersltd.co.uk/red-light-flashing-on-boiler/
- Digital Spy Forum. (2016, June 5). Boiler reset button keeps flashing red… Retrieved from https://forums.digitalspy.com/discussion/2153935/boiler-reset-button-keeps-flashing-red
- JustAnswer. (2022, December 14). My reset button keeps flashing and I have no heating or hot water. Retrieved from https://www.justanswer.co.uk/hvac/ktb8x-reset-button-keeps-flashing-no-heating-hot.html
- Smart Cover Insurance. (2023, January 24). Boiler flashing red light? | Steps to reset. Retrieved from https://smart-cover.co.uk/blogs/boiler-flashing-red-light
- Skills Training Group. (n.d.). How To Reset Your Boiler In 3 Simple Steps. Retrieved from https://www.skillstg.co.uk/blog/how-to-reset-your-boiler/
